Emerson SW375 or SW105 to RCK55 Conversion

SW375 w/ SW350 to RCK55 w/ SW605 Conversion kit

Emerson SW375/SW105 to RCK55 w/ SW605 conversion kit(wall control)

This kit will convert older Emerson fans with the SW375 or SW105 receivers and SW350 or SW115 wall control to the current RCK55 and SW605 wall switch. You can add a hand held remote SR600.

 

 

 

 

SW375 w/ SR330 to RCK55 w/ SR600 Conversion kit

 Emerson SW375 / SR330 or SW105 / SR110 to RCK55 w/ SR600 Conversion kit

This kit will convert older Emerson fans with SW375 or SW105 receivers and SR330 or SR110 transmitters, to the RCK55 receiver with SR600 remote.

All kits are new Emerson parts. Instructions included, call us with any questions. 952-683-9450

www.FanManLighting.com 

9342902000 Casablanca Stealth Glass Conversion Kit

www.FanManLighting.com

9342902000 Stealth Glass Conversion Kit


Conversion pan and glass kit for ALL Casablanca Stealth model ceiling fans beginning with "32". exa: 32xxT, 32xxA, 32xxR, 32xxZ

Another exclusive item from Fan Man Lighting!

www.FanManLighting.com

K190301045

Glass only for all newer Casablanca Stealth ceiling fans beginning with model number "59". 














Call us at 952-683-9450 with any questions.

Fan Man Lighting
www.FanManLighting.com

Casablanca Inteli Touch operation

Call The Fan Man with ANY questions! 952-683-9450

www.FanManLighting.com

INTELI•TOUCH OPERATION^© POWER

Programmed into every Inteli-Touch Series fan is an Automatic Demonstration Program. It can be used to fully demonstrate and test the operation of the fan.
To enter the demonstration program:
1. Turn off for at least three seconds. This will clear the fan memory ready for programming.
2. Turn on.
3. Immediately operate the buttons in the following sequence: FAN – LIGHT – FAN – LIGHT – FAN a multi-tone signal will verify the start of the test program which proceeds as follows:

• Lights slowly increase to full intensity.o Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short time).
• Lights turn off.

The complete cycle lasts slightly over one minute. It will continue to repeat until the is turned off for more than three seconds, canceling the program.
The button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter additional programs. POWER must be left on to retain a previously set fan speed or light level.

INTELI•TOUCH OPERATION^© SPEED CONTROL

FAN CONTROL ON – OFF: A momentary press of the FAN button
CHANGE SPEED: Press and hold FAN button longer than one second
There are six individual speed settings for the fan; each speed is indicated by an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled . The fan blades will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached. The fan speed is now in memory and will automatically come on at the same speed each time the button is used. To maintain this level of speed, turn the fan on by pressing less than one second. To lower speed, turn fan off, then on by pressing and holding the button until the desired speed is reached. When the fan is on, you may increase the speed by pressing and holding the button until the desired speed is reached, then release it.

INTELI•TOUCH OPERATION^© REVERSING AIRFLOW

The direction of airflow can be changed from downward to upward or from upward to downward.
To reverse the airflow:
1. Make sure the is on.
2. Press the button. 
Note: A four-toned signal indicates the command was accepted by the fan. A few seconds later the fan will slow to a stop and then reverse direction.

INTELI•TOUCH OPERATION^© LIGHT

LIGHT CONTROL ON – OFF: A momentary press of the LIGHT button
CHANGE BRIGHTNESS: PRESS AND HOLD LIGHT BUTTON LONGER THAN ONE SECOND
To turn the lights off and on, press and release the button for less than one second.
To vary the light brightness:
1. With lights off, press and hold the button. After one second the lights come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached. The brightness level is now in the fan memory and will automatically come on at the same brightness the next time the button is used. To maintain this level of brightness, press the button for less than one second. To lower the brightness, turn the lights off, then press and hold the button until the desired brightness level is reached.
When the light is on, you may increase the brightness level by pressing and holding the button until the desired level is reached, then release it.

AUTOMATIC DEMONSTRATION PROGRAM

The Light-Minder program automatically turns OFF the fan mounted lights after two hours.
To enter the Light-Minder Program:
1. Turn the OFF for at least three seconds.
2. Turn the ON.
3. Immediately operate the buttons in the following sequence: DEMO: FAN – LIGHT – FAN – LIGHT – FAN
4. A series of tones indicates this command has been accepted. The fan and light will operate normally using the buttons to turn them on and off. But, if the lights are left on, they will automatically shut off after two hours.
To cancel the Light-Minder Program, turn the off for three seconds.

INTELI•TOUCH OPERATION^© SAFE-EXIT^® PROGRAM

The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out.
To enter the Safe-Exit Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence: SAFE EXIT: FAN – FAN – LIGHT – LIGHT
After you hear the confirming audio tones from the fan – immediately press
4. The lights will blink to indicate this command has been accepted. The lights will stay on for twenty seconds and then begin to dim. After a total of thirty seconds has elapsed, the lights will be off completely.
To cancel the Safe-Exit Program, turn the off for three seconds.

INTELI•TOUCH OPERATION^© HOME-SAFE^® PROGRAM

The Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times.
To enter the Home-Safe Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence: HOME SAFETY: LIGHT – FAN – LIGHT – FAN
4. A tone and flashing light indicate this command has been accepted. This program overrides all manual control of lights and fan. The lights will now be automatically cycled on and off in a controlled sequence as follows: On 1 hour, off 1/2 hour, on 2 hours, off 1 hour, on 1/2 hour then off 2 hours. This seven hour pattern will repeat continuously so that a different pattern of lighting is seen each day of the week.
To cancel the Home-Safe Program, turn the off for three seconds.

INTELI•TOUCH OPERATION^© FAN-MINDER™ PROGRAM

The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for the cooling night air.
To enter the Fan-Minder Program:
1. Turn the off for at least three seconds.
2. Turn the on.
3. Immediately operate the buttons in the following sequence: FAN MINDER: LIGHT – LIGHT – FAN  – FAN
4. The fan controller will respond with three descending tones. A timer is now initiated and the fan will reduce one speed for each two-hour interval. The fan will not, however, descend below the second lowest speed.
To cancel the Fan-Minder Program, turn the off for three seconds. You may increase the fan speed by pressing and holding the button until the desired speed is reached, then release it. The fan will again reduce one speed for each 2 hour interval.

INTELI•TOUCH OPERATION^© LIGHT-MINDER^® PROGRAM

Note: Both Light-Minder and Safe-Exit programs can run at the same time, however the dimmer cannot be used, the light may only be turned ON/OFF.

NO FAN OR LIGHT –
Check main circuit fuses, curcuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection.
FAN WOBBLES –
Be sure canopy pin is properly set into the slot on the ball
SHAKES EXCESSIVELY –
Check the screws holding the blade holders to the fan motor. Tighten as necessary.·
Check the angle of the blades to make sure that a blade holder has not been bent during installation.
FAN NOISY DURING OPERATION –
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
Tighten canopy screws and mounting plate assembly.
Tighten the blade to bladeholder screws and blade holders to flywheel.
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have fallen off the wire splices. Tighten or adjust as necessary.
BREAK-IN PERIOD –
Let fan run at high speed for two (2) hours
DOES NOT RUN ON LOW –
If new, “break-in” may be required – run at higher speed for several days
SPEED LIGHTS FLASH OR BLINK DURING OPERATION OF W-32 WALL CONTROLS/FAN MAY ROTATE OR MAKE AUDIBLE TONES DURING OPERATION OF THE W-11 AND W-12 WALL CONTROLS: Normal operation.WHEN AC POWER IS TURNED ON FOR THE FIRST TIME, THE LIGHTS OPERATE NORMALLY, BUT W-32 WALL CONTROL OPERATION IS REVERSED: FAN BUTTON OPERATES THE LIGHTS; LIGHT BUTTON OPERATES THE FAN: Reverse the 2 black and white striped wire connections.FAN OR LIGHTS APPEAR TO OPERATE BY THEMSELVES (CHANGING SPEED OR INTENSITY), WALL CONTROL OPERATION IS INTERMITTENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit board assembly.

Call The Fan Man with ANY questions! 952-898-2754

www.FanManLighting.com

Casablanca's "New Platform" or "Universal Remote" system.

Casablanca K0223-01 www.FanManLighting.com

Casablanca 99020 www.FanManLighting.com

Most Casablanca Fans from 2013 on Utilize this New System. If Your Fan Model Begins With the Number "5" eg: 5xxxx, This is the Correct System.

Wall control:  K022301000 (K0223-01) 

Hand Held control: 99020

Receiver: K021906000 (K0219-06) If Your Fan Remote System is Acting Up eg: Fan Speed Problems or Light Problems This is Usually the Failure Point, More So than the Transmitter.

Call us with any troubleshooting questions. 952-683-9450

Fan Man Lighting
www.FanManLighting.com
15465 Cedar Ave
Apple Valley, MN. 55124

Casablanca Inteli-Touch 3 Conversion kits

Casablanca G265802000 FanManLighting.com

Casablanca has discontinued parts for all W-11/12 and W-32 Inteli-Touch control systems.

The kits listed below provide everything needed to convert older Casablanca Inteli-Touch ceiling fans to the new Inteli-Touch 3 system. Follow the links to our main website, or call the store with any questions.

Inteli-Touch 3 conversion kits.

Kits include circuit board, wall control, and conversion plugs.

G265802000 or IT3Kit For most Casablanca Inteli-Touch Fans 1987 & newer including Panama(12XXXT & 66XXT), Victorian(2XXXT & 63XXT) and many other models. Kit includes: 8880602000 circuit board, W-85 wall control and 7731901000 conversion plug.

G265803000 or IT3Kit-S For Casablanca Inteli-Touch fans Stealth(32XXT), Bel Air(38XXT), and Venus(24XXT) models. Kit includes: 8907101000 circuit board, W-85 wall control and 7731901000 conversion plug.

G265805000 or IT3Kit-M For Casablanca Inteli-Touch fans Mission(970XXT), Cathay(98XXT), and Nouvelle(96XXT) models. Kit includes: 8880603000 circuit board, W-85 wall control, and 7731901000 conversion plug.

 IT3Kit-86 For Casablanca Inteli-Touch fans 1986 & Older including Zephyr(1XXXT), Older Panama, 4 Seasons, and Victorian models. Kit includes: 8880602000 circuit board, W-85 wall control and  P-FM2011-3 and
P-FM2011-2 conversion plugs.

Call us with your model and serial number.

Fan Man Lighting
952-683-9450
www.FanManLighting.com 
www.FanManRepair.com

GF516A G9374 Minka Aire glass diffuser replacement

www.FanManLighting.com

Fan Man Lighting stocks replacement glass shades for Minka Aire ceiling fans. Visit us at www.FanManLighting.com or give us a call.

Minka Aire glass replacement diffusers:

GF516 Or GF516A Glass replacement for Concept I and Concept II models. F516, F517, F518, F519.

G9374 Glass replacement for Supra 44" fans and K9374L light kits. Ceiling fan models: F563-SP in all colors.

Listed above are the two most common Minka Aire glass diffusers. For more options click: Minka Aire glass and parts or give us a call

Fan Man Lighting
952-898-2754 or 1-866-600-FANS(3267)
www.FanManLighting.com

Repair parts for Casablanca Inteli-Touch 3 system, W-85

Casablanca W-85 www.FanManLighting.com

| Fan Man Lighting | Authorized Casablanca Parts & Service |

Casablanca's Inteli-Touch 3 system uses the W-85 wall control. W-85 wall controls will operate both single circuit and 3-way wiring situations.

The W-85 is the replacement part for all W-11, W-12, W-32, and W-31 Inteli-Touch wall controls. To convert to the new system, you will also need a new circuit board and conversion plug (*note the BFR is not used with IT3). Fan Man Lighting has created conversion kits for each series of Inteli-Touch ceiling fan. Inteli-Touch Diagnostic/Troubleshooting.



Questions? Call us with your model and serial number 952-898-2754 or 952-683-9450

Protect your ceiling fan controls from excessive transient voltages with a Varistor.


These items and more available online www.FanManLighting.com